Koozali.org formerly Contribs.org

Trying to run the Mirror

Offline mgb

  • ****
  • 557
Trying to run the Mirror
« on: December 11, 2012, 12:17:12 PM »
Trying to run the Mirror
Not a week has advanced 2.6%
  SME 7.6
Installing the Mirror of SME
Half a year ago was successfully added Mirror
It is used as a backup after the Mirror
Disconnect the old disk
/raid.JPG
« Last Edit: December 11, 2012, 12:31:26 PM by mgb »
Thanks all for helping
Skype yosii2009

Re: Trying to run the Mirror
« Reply #1 on: December 12, 2012, 11:42:34 PM »
mgb, if you are having problem updating your server, check:
http://forums.contribs.org/index.php/topic,49361.0.html

Hope it helps.
- chris
If it does not work out of the box, please fill in a Bug Report @ Bugzilla (http://bugs.contribs.org)  - check: http://wiki.contribs.org/Bugzilla_Help .  Thanks.

Offline TerryF

  • grumpy old man
  • *
  • 1,120
Re: Trying to run the Mirror
« Reply #2 on: December 12, 2012, 11:47:35 PM »
Trying to run the Mirror
Not a week has advanced 2.6%
  SME 7.6
Installing the Mirror of SME
Half a year ago was successfully added Mirror
It is used as a backup after the Mirror
Disconnect the old disk
/raid.JPG

I "think" this about a failed raid that is not syncing.

Then again..
--
qui scribit bis legit

Re: Trying to run the Mirror
« Reply #3 on: December 12, 2012, 11:53:22 PM »
I "think" this about a failed raid that is not syncing.

Then again..

Trex, you are correct. My bad, need a strong coffee...
mgb, ignore my post.
- chris
If it does not work out of the box, please fill in a Bug Report @ Bugzilla (http://bugs.contribs.org)  - check: http://wiki.contribs.org/Bugzilla_Help .  Thanks.

Offline mgb

  • ****
  • 557
Re: Trying to run the Mirror
« Reply #4 on: December 13, 2012, 01:58:48 PM »
Thank you
I installed yum update
Work waiting for the end of the Mirror

Created a new problem
After the signal-event post-upgrade; signal-event reboot
  stop is active
i login the alt + f2
  Running ini3
the init 7
is begin to work

In any event
Activated waiting for the end of the Mirror
Thanks all for helping
Skype yosii2009

Offline mgb

  • ****
  • 557
Re: Trying to run the Mirror
« Reply #5 on: December 17, 2012, 08:52:48 AM »
After Update
Mirror stops and starts again Cannot finish Mirror
Thanks for any idea to the
Solution

Thanks all for helping
Skype yosii2009

Offline TerryF

  • grumpy old man
  • *
  • 1,120
Re: Trying to run the Mirror
« Reply #6 on: December 17, 2012, 08:59:34 AM »
After Update
Mirror stops and starts again Cannot finish Mirror
Thanks for any idea to the
Solution

Have to say that you need to find somone to post for you in english or use one of the non-english forums because I am not sure what you are asking.

I "think" it is about a non syncing Raid, and if that is what it is, you need to be very very sure about what is being said to do or NOT to do.

--
qui scribit bis legit

Offline janet

  • ****
  • 4,779
Re: Trying to run the Mirror
« Reply #7 on: December 17, 2012, 11:08:46 AM »
mgb

That screen image data looks like something is wrong.
One of your disks may be faulty.
I suggest you remove the new disk you added and try another.

Also run a test on both disks before proceeding any further.
Boot up to the sme install CD in Rescue mode and run smartctl, refer
http://wiki.contribs.org/Monitor_Disk_Health

or boot up to the UBCD (Ultimate Boot CD) & run a test on both drives using the appropriate manufacturers drive diagnostic utility.
Search Google for UBCD
Please search before asking, an answer may already exist.
The Search & other links to useful information are at top of Forum.

Offline mgb

  • ****
  • 557
Re: Trying to run the Mirror
« Reply #8 on: December 18, 2012, 08:18:08 AM »
I thank the answer
I turned
Here are the results log
Quote
smartctl version 5.33 [i686-redhat-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     SAMSUNG HD103SJ
Serial Number:    S246JDWSB67512
Firmware Version: 1AJ100E4
User Capacity:    1,000,204,886,016 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   8
ATA Standard is:  Not recognized. Minor revision code: 0x28
Local Time is:    Tue Dec 18 08:59:22 2012 IST

==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details.

SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===

Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      ( 137) Reserved.
Total time to complete Offline
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      ( 137) Reserved.
Total time to complete Offline
data collection:                 (9240) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off sup$
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        ( 154) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN$
  1 Raw_Read_Error_Rate     0x002f   001   001   051    Pre-fail  Always   FAIL$
  2 Throughput_Performance  0x0026   252   252   000    Old_age   Always       $
  3 Spin_Up_Time            0x0023   074   073   025    Pre-fail  Always       $
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       $
  5 Reallocated_Sector_Ct   0x0033   252   252   010    Pre-fail  Always       $
  7 Seek_Error_Rate         0x002e   252   252   051    Old_age   Always       $
  8 Seek_Time_Performance   0x0024   252   252   015    Old_age   Offline      $
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       $
 10 Spin_Retry_Count        0x0032   252   252   051    Old_age   Always       $
 11 Calibration_Retry_Count 0x0032   252   252   000    Old_age   Always       $
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       $
191 G-Sense_Error_Rate      0x0022   252   252   000    Old_age   Always       $
192 Power-Off_Retract_Count 0x0022   252   252   000    Old_age   Always       $
194 Temperature_Celsius     0x0002   059   054   000    Old_age   Always       $
195 Hardware_ECC_Recovered  0x003a   100   100   000    Old_age   Always       $
196 Reallocated_Event_Count 0x0032   252   252   000    Old_age   Always       $
197 Current_Pending_Sector  0x0032   100   100   000    Old_age   Always       $
198 Offline_Uncorrectable   0x0030   252   252   000    Old_age   Offline      $
199 UDMA_CRC_Error_Count    0x0036   200   200   000    Old_age   Always       $
200 Multi_Zone_Error_Rate   0x002a   100   100   000    Old_age   Always       $
223 Load_Retry_Count        0x0032   252   252   000    Old_age   Always       $
225 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       $

SMART Error Log Version: 1
ATA Error Count: 9716 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
 CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 9716 occurred at disk power-on lifetime: 23001 hours (958 days + 9 hours)
  When the command that caused the error occurred, the device was active or idl$

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 b8 4a 9c 2c ee  Error: UNC 184 sectors at LBA = 0x0e2c9c4a = 237804618

 Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 d8 2a 9c 2c ee 08      00:22:56.417  READ DMA
  ec 03 46 00 00 00 a0 08      00:22:56.417  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 08      00:22:56.417  SET FEATURES [Set transfer mode]
  ec 00 b8 4a 9c 2c a0 08      00:22:56.417  IDENTIFY DEVICE
  c8 00 e0 22 9c 2c ee 08      00:22:56.416  READ DMA

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LB$
# 1  Extended offline    Completed: handling damage??  90%     23003         -
# 2  Short offline       Completed: handling damage??  90%     23003         -
# 3  Extended offline    Completed: handling damage??  90%     22983         -
# 4  Short offline       Completed: handling damage??  90%     22983         -

SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1
SMART Selective self-test log data structure revision number 0
Warning: ATA Specification requires selective self-test log data structure revi$
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Completed_handling_damage?? [10% left] (0-65535)
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Thanks all for helping
Skype yosii2009

Offline janet

  • ****
  • 4,779
Re: Trying to run the Mirror
« Reply #9 on: December 18, 2012, 09:00:21 AM »
mgb

Quote
Drive failure expected in less than 24 hours. SAVE ALL DATA.

Like I said, change the faulty drive
Please search before asking, an answer may already exist.
The Search & other links to useful information are at top of Forum.