Koozali.org formerly Contribs.org

[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem

Offline dtech

[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem
« Reply #30 on: July 18, 2006, 01:43:21 PM »
I just wanted to add another successful install of the July 2 RPMs (I used the yum localinstall method, no problems).

bradleyj00

SME7 horde/kronolith
« Reply #31 on: July 19, 2006, 07:49:31 PM »
I've been trying to install kronolith, and hopefully other horde applications on my new SME7 server.

I've followed the steps as documented by jfarschman, but I run into an "unsupported scheme" error when issuing the first command line.

Any suggestions?

Any direction would be appreciated.

Jim




[root@sme7 ~]# wget -r -l1 -A.rpm --no-parent \ http://mirror.contribs.org/smeserver/contribs//jbennett/sme7/horde/RPMS/
 http://mirror.contribs.org/smeserver/contribs//jbennett/sme7/horde/RPMS/: Unsupported scheme.

FINISHED --15:11:53--
Downloaded: 0 bytes in 0 files

[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem
« Reply #32 on: July 19, 2006, 08:57:44 PM »
Try taking the forward slash out and putting it all on the same line.

Code: [Select]

wget -r -l1 -A.rpm --no-parent http://mirror.contribs.org/smeserver/contribs//jbennett/sme7/horde/RPMS/


That should work
Jay Farschman
ICQ - 60448985
jay@hitechsavvy.com

bradleyj00

sme 7 horde/kronolith
« Reply #33 on: July 19, 2006, 09:05:36 PM »
That worked! Thanks for your assistance.

Being kind of new to this, I guess I took the whole command structure very literally.

Much appreciated.
Jim

Offline jumba

  • ****
  • 291
  • Donations: July 2007 - $ 20.00
    • Smeserver på svenska!
[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem
« Reply #34 on: July 20, 2006, 09:30:25 PM »
...just another successful install of the July 2 RPMs using the yum localinstall method.

No problems

I installed all RPMs and I now have a very comprehensive "webmail"  :-D

Thanks a lot!

[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem
« Reply #35 on: July 22, 2006, 08:54:26 AM »
John,
Thanks for your work.
Installation went well, most everything seems to work ok   EXCEPT  for File Manager.
When I click on File Manager, in the middle of the screen I see a: File Manager Login message and a login button. When I click on the button, the screen goes white for a second and goes back to the same message.
SME user and community member since 2005.
Want to install Wordpress in iBay of SME Server?
See my step-by-step How-To wiki here:
http://wiki.contribs.org/Wordpress_Multisite

Offline brianr

  • *
  • 907
[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem
« Reply #36 on: July 22, 2006, 11:08:41 AM »
I just installed the mimp and e-smith-horde RPMs, but cannot see how or where to access mimp.

Can someone point me in the right direction?
Brian j Read
(retired, for a second time, still got 3 installations though)
.........

[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem
« Reply #37 on: July 25, 2006, 02:03:03 PM »
Quote from: "calisun"
John,
Thanks for your work.
Istallation went well, most everything seems to work ok   EXCEPT  for File Manager.
When I click on File Manager, in the middle of the screen I see a: File Manager Login message and a login button. When I click on the button, the screen goes white for a second and goes back to the same message.


It's the same for me

[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem
« Reply #38 on: July 31, 2006, 02:26:02 PM »
JB,

Happy to report another successful install (although got the same problem with file-manager that has already been reported).

My question is a little different & I'm not sure if you can help, but ....

I've just updated my cyrus-imap contrib for sme7 (see http://forums.contribs.org/index.php?topic=33072.msg140466#msg140466).  I use this contrib in conjuction with a commercial product called Toltec connector to enable users who run Outlook to share folders (calendar, contacts etc) via SME, rather than needing Exchange.

The latest release of the connector stores its data in Kolab2 XML format, which it claims can then be read by compatible clients to provide web access to the data.  According to the Kolab site, Horde is one of the compatible clients (albeit under development - see http://www.kolab.org/about-kolab-clients.html).

I've installed your contrib, which works well - but do you have any idea how I tell Kronilith to look at a user IMAP folder and interpret the messages there as XML calendar entries?

I guess you must be busy with your own contrib - but if you (or anyone else) has any suggestions where I should start looking, I'd be grateful.

Thanks
Jon
......

Offline mrjhb3

  • *
  • 1,187
    • John Bennett Services
[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem
« Reply #39 on: August 01, 2006, 08:55:00 AM »
Quote from: "rich"
hey mrjhb3 . . .

Thanks for all your efforts with this . . .

I have upgraded to your new RPMs and now my cron error is fixed.
Only problem is I am not getting any email reminders.

Any tips where to begin troubleshooting?

Thanks again.


You must have a default identity set for reminders to work.  Options/horde or options/mail.

JB
......

[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem
« Reply #40 on: August 02, 2006, 03:59:51 AM »
John,
I went through your previous posts, and you said: "If you want to use Gollem, then you must enable ftp on the local network"
My ftp is enabled for local network (and it always has been) and I can't get file manager to work.
SME user and community member since 2005.
Want to install Wordpress in iBay of SME Server?
See my step-by-step How-To wiki here:
http://wiki.contribs.org/Wordpress_Multisite

Offline mrjhb3

  • *
  • 1,187
    • John Bennett Services
[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem
« Reply #41 on: August 02, 2006, 04:41:47 AM »
Quote from: "calisun"
John,
I went through your previous posts, and you said: "If you want to use Gollem, then you must enable ftp on the local network"
My ftp is enabled for local network (and it always has been) and I can't get file manager to work.


Did you install gollem after the other rpms?  If so, you need to do a signal-event email-update so that the gollem config templates will be expanded.

If that was already done, then check you gollem/config/backends.php file.  You should have something similiar to:

//00Header
// * $Horde: gollem/config/backends.php.dist,v 1.41.2.6 2006/02/22 06:48:37 slusarz Exp $

//100LocalFtp
// This backend uses Horde credentials to automatically log in.
$backends['hordeftp'] = array(
    'name' => 'Local FTP Server',
    'driver' => 'ftp',
    'preferred' => '',
    'hordeauth' => true,
    'params' => array(
        // The hostname/IP Address of the FTP server.
        'hostspec' => 'ftp.mytestserver.com',        <--check this line
        // The port number of the FTP server.
        'port' => 21,
        // Use passive mode?
        'pasv' => false,
        // Set timeout (in seconds) for the FTP server. Default: 90 seconds
        // 'timeout' => 90,
        // If true and the POSIX extension is available the driver will map
        // the user and group IDs returned from the FTP server with the local
        // IDs from the local password file.  This is useful only if the FTP
        // server is running on localhost or if the local user/group
        // IDs are identical to the remote FTP server.
        // You must be running a version of Horde >= 3.1 for this parameter to
        // have any effect.
        // 'maplocalids' => true
    ),
    'loginparams' => array(
        // Allow the user to change the FTP server.
        // 'hostspec' => 'Hostname',
        // Allow the user to change the FTP port.
        // 'port' => 'Port'
    ),
    // 'root' => '',
    // 'home' => '',
    // 'createhome' => false,
    // 'permissions' => '750',
    // 'filter' => '^regex$',
    // 'quota' => false,
    'clipboard' => true,
    'attributes' => array('type', 'name', 'download', 'modified', 'size', 'permission', 'owner', 'group')
);


JB
......

[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem
« Reply #42 on: August 02, 2006, 05:44:31 PM »
I am not sure what order they were installed, I did:

wget -r -l1 -A.rpm --no-parent http://mirror.contribs.org/smeserver/contribs//jbennett/sme7/horde/RPMS/

yum localinstall *.rpm

signal-event post-upgrade

signal-event reboot



As far as gollem/config/backends.php, I will check it tonight




-
SME user and community member since 2005.
Want to install Wordpress in iBay of SME Server?
See my step-by-step How-To wiki here:
http://wiki.contribs.org/Wordpress_Multisite

[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem
« Reply #43 on: August 03, 2006, 08:43:48 PM »
John
I did check my backends.php, it looks identical to the example you have posted. The line that you marked to <--check this line
" 'hostspec' => 'ftp.mytestserver.com', <--check this line" does show my correct server name.

My question is, since the ftp is set to accept ftp from local network only, should't the line look something like this?
 'hostspec' => 'ftp.192.168.1.1',
SME user and community member since 2005.
Want to install Wordpress in iBay of SME Server?
See my step-by-step How-To wiki here:
http://wiki.contribs.org/Wordpress_Multisite

Offline mrjhb3

  • *
  • 1,187
    • John Bennett Services
[Announce] RPM's for Kronolith, Nag, Mnemo, and Gollem
« Reply #44 on: August 04, 2006, 04:32:11 AM »
Quote from: "calisun"
Installation went well, most everything seems to work ok   EXCEPT  for File Manager.
When I click on File Manager, in the middle of the screen I see a: File Manager Login message and a login button. When I click on the button, the screen goes white for a second and goes back to the same message.


Missed some of these posts as sometimes the forums do not send out an email for threads that have been updated.

For everyone getting an error with gollem, I can not duplicate this.  Over the weekend, I'll load my test servers again with the rpms on my contribs site and see if I can duplicate the errors.  Can someone look at their log /var/log/messages and see if you have any errors when clicking on file manager.

The reason that ftp.mytestserver.com works is that this is an host entry on SME server so it resolves locally.  localhost may work as well, I haven't tested it.  My remote access settings are set to allow access only from local networks and to accept passwords only from local networks.

JB
......